Second hand placement machine recycling - how to do maintenance and inspection for Panasonic placement machine?
Author:Li qiuhao Time:2021-06-09 09:17 Browse(818)
Second hand placement machine recycling - how to do maintenance and inspection for Panasonic placement machine, Touch screen and OLED Forum
With the development of electronic technology and the improvement of the profitability of SMT electronic market, the SMT equipment industry in Shenzhen and Guangdong is surging. After all, for small and medium-sized enterprises, the cost of buying a new Panasonic mounter is a little high, so many small enterprises are investing in the second-hand Mounter market. How to maintain and inspect the second-hand Panasonic Mounter? Next, Zhichi technology will analyze with you:   R1 U( g# N7 O- t4 W0 C9 U3 ~( J+ [& n        1、 After a long period of use, the feeding mechanism can access the feeder at a high speed.
however, after a long period of use, the feeding mechanism has a high-speed access to the feeder, The pawl of the feeder is seriously worn.

Second hand placement machine recycling - how to do maintenance and inspection for Panasonic placement machine?

the feeder with worn pawl wheel should be repaired immediately.
if it cannot be repaired, it should be replaced in time.
6 V7 Y7 C5 g) B; S.
_" B' c5 @8 }( O% g        2、 Deformation of feeder structure due to long-term use or improper operation by operators, deformation and corrosion of pressing band cover plate, thimble, spring and other moving mechanisms, resulting in device deviation, vertical piece or failure to absorb the device.
poor lubrication of feeder generally causes maintenance of feeder.
it is easy to be ignored, but regular cleaning, cleaning and maintenance are necessary Oiling and lubrication is essential.
in order to improve the quality of the products, it is necessary to add oil and lubrication    L# d    s/ @" i5 A# V9 I- l0 }8 W7 B5 f! C5 Q% ]& c       3、 The influence of suction nozzle is another important factor affecting the mounting rateWhen the vacuum negative pressure is insufficient, the mechanical valve on the mounting head will be automatically switched before the suction nozzle takes the part, and the mechanical valve will be converted from blowing to real adsorption, which will produce a certain negative pressure. When the negative pressure sensor detects the value within a certain range after the part is sucked, the machine will be normal, otherwise the suction is bad.
the most basic work in the test is also very important, which is often ignored or despised in the actual process, It often brings a lot of trouble to the manufacturing process.
the process is very complicated2 m.
v& |: C$ S6 h5 f1 L7 e+ Y. I; w* Q3 q5 n9 n        4、 Clean the filter in the vacuum pump regularly to ensure sufficient negative pressure; At the same time, the working state of the negative pressure detection sensor should be checked regularly.
the filter on the mounting head and the filter on the suction nozzle are black due to the pollution and blockage of the surrounding environment or the impure gas source.
: U5 m + K $j 1 O 3 U7 {0 P}5 v9 i2 M; l- U6 g: A4 b( [       5、 The filter should be replaced regularly.
generally, the filter on the suction nozzle should be replaced at least once every half a month, and the filter on the mounting head should be replaced at least once every half a year, so as to ensure the smooth air flow.
the pressure of the air source circuit should be relieved.
such as the aging and cracking of the rubber pipe, the aging and wear of the seal, and the wear of the suction nozzle after long-term use, etc, In particular, a large number of scraps are produced after cutting off the components of paper tape packaging.
the results show that the paper tape packaging can reduce the waste of the components4 J6 o; E% W4 |/ |" V% r' `) B       Shenzhen Zhichi technology supplies Panasonic mounter, JUKI mounter, reflow soldering, AOI detector for a long time.
solder paste printing machine and SMT peripheral equipment.
it is specialized in providing sales, recycling, leasing, maintenance and other services.
Shenzhen Zhichi Technology Co., LtdWe will reasonably configure the required models according to the actual production needs of your company's products.
we will provide one-stop SMT production line supporting solutions.
we will provide one-stop SMT production line supporting solutions% f# @; k6 S% M( `3 g: K* J4 K1 m8 U" z4 q. O.
.
.
.
.
.
Related topics